Dmg Luxabond

Dmg Luxabond

₹5,348.00 ₹5,500.00 -3%
Brand: DMG
Product Code: DMG-LUX
Availability: Out Of Stock

OverView

Totaletch Bond...

Totaletch Bond

 LuxaBond-Total Etch is a dual-cure bonding agent for enamel and dentin, suitable for use with dual-cure and self-cure composites, such as LuxaCore Z-Dual. It is necessary to etch enamel and dentin surfaces prior to application. Due to the dual-cure nature of the material, LuxaBond-Total Etch is particularly useful when bond-ing posts in areas where light can’t penetrate.

 COMPOSITION:

Pre-bond: Ethanolic aryl sulfonate solution

Bond A: Hydrophilic Bis-GMA based resin matrix, catalyst

Bond B: Hydrophilic Bis-GMA based resin matrix, benzoyl peroxide

INDICATIONS:

Used in conjunction with total etch technique for core build ups and addition of resin cements for posts, crowns, bridges, inlays.


FEATURES:

  • Indicated for bonding of posts, cores, crowns, bridges, inlays and onlays
  • Cures without a light; can be used for all indirect procedures
  • Better adhesion
  • Specifically shaped Endobrushes for an easier application in the root canal
  • Non-acetone, non-alcohol formulation.

KEY SPECIFICATIONS :

TECHNICAL DATA:

Working time of the mixture of bond A + bond B (storage in a dark place) : 5 min

Reaction time of the etching gel to enamel : 20 to 60 s

Reaction time of the etching gel to dentin max.: 15 s

Pre-bond work-in time : 15 s

Mixing time of bond A + bond B : 5 s

Bond A + bond B work-in time : 20 s

LuxaBond-Total Etch exposure time min. : 10 s


DIRECTIONS TO USE :

Use in the root canal, for cementing root posts, for cementing inlays

Follow the Steps:

1. Prepare the root canal or cavity in accordance with the general rules for adhesive procedures. We recommend the use of a rubber dam.

2. Etch dentin and enamel with 37 % phosphoric acid gel or similar. Start the etching process with the enamel and then expand this to include the dentin. The reaction time on the enamel should be 20 to 60 s. The reaction time on the dentin must not exceed15 s.

Please note: When using LuxaBond-Total Etch it is essential to etch the affected enamel and dentin surfaces.

3. Rinse with water for a minimum of 15 seconds.

4. Remove general water excess. After the rinsing process, an even moist layer must remain on the dentin surface requiring treatment. If necessary, wet the dentin surface using a lightly moistened micro brush.

5. Use a brush to work 1 to 2 drops of pre-bond into the etched tooth structure for 15 s. Remove any excess, e.g. with a paper tip. Blow gently using oil and water-free air. The surface should appear evenly moist.

6. Mix 1 to 2 drops of bond A and bond B in a trough in the mixing palette at a ratio of 1:1 for approx. 5 s and work into the tooth structure for 20 s using a micro brush.

7. Carefully remove bond excess from the preparation, e.g. with a paper tip, and then gently blow with oil and water-free air until the surface appears evenly

moist.

8. Apply the attaching cement in accordance with the manufacturer’s instructions.


PACKAGING:

  • 5ml bottle Bond A
  • 5ml bottle Bond B
  • 2ml syringe Etch Gel Medium Viscosity
  • 25 red Endobrushes
  • 25 Black Endobrushes
  • 3 Luer-lock Tips
  • 1 mixing palette 

Write a review

Note: HTML is not translated!
    Bad           Good